Abstract

Heavy vehicles behave differently from ordinary passenger cars due to their characteristics such as size and operational performance. At roundabout, entry capacity estimation mainly focuses on passenger cars. In HCM 2010, the impact of heavy vehicles on entry capacity is considered through a heavy vehicle adjustment factor fHV which includes heavy vehicle percentage and passenger car equivalent (PCE hereafter) value. It is generally set as 2.0, which means a heavy vehicle is assumed to be equivalent to two passenger cars. In existing methods, the PCE value at roundabouts is estimated based on several considerations such as entry capacity and move-up time. All of these considerations are influenced by local driver behavior and geometry conditions. Thus, this paper aims to estimate entry capacity considering the characteristics of heavy vehicle behavior in Japan. In this paper, characteristics of heavy vehicle behavior such as speed and gap parameters are firstly analyzed by using data observed at several roundabouts in Japan. Then, a simulation study which is calibrated based on the observation data is conducted by applying VISSIM 5.40. Roundabout entry capacity is estimated through assuming different heavy vehicle percentage values of each entry. Based on the estimated results of entry capacity, PCE value is calculated. The PCE values from the simulation study are compared with those values adopted by several design guidelines. Through the empirical analysis, it is found that heavy vehicles move in lower speed than passenger cars in the process of travelling roundabouts. The headways which are formed by heavy vehicles are commonly greater than those only formed by passenger cars. Then, PCE values which are calculated from simulation output are shown to change with different combinations of heavy vehicle percentage of each entry. The results in this paper provide a reference for roundabout entry capacity estimation considering heavy vehicle behavior in Japan. Future works are some further analysis from the viewpoint of geometry, since heavy vehicle behavior is significantly influenced by roundabout geometry such as inscribed circle diameter and circulatory roadway width, particularly at compact roundabout which is often the case in Japan.

Keywords

heavy vehicle ; roundabout entry capacity ; empirical analysis ; simulation study

References

  1. Akçelik, 1998 Akçelik, R. (1998), Roundabouts: capacity and performance analysis. ARRB Research Report ARR 321, Vermont, Australia, 150p.
  2. Highway, 2010 Highway Capacity Manual (2010). Transportation research board.
  3. Kang, 2015 N. Kang, H. Nakamura; Estimation of roundabout entry capacity considering conflict with pedestrians; Transportation research record, Journal of the Transportation Research Board, 2517 (2015), pp. 61–70
  4. Lee., 2015 Lee., C. (2015), Developing passenger-Car Equivalents for Heavy Vehicles in Entry Flow at Roundabouts, American Society of Civil Engineers, 04015013.
  5. SI for roundabouts, 2011 SIDRA for roundabouts (2011). SIDRA for roundabouts manual.
  6. Tanyel, 2001 Tanyel, S. (2001), Türkiye.deki Dönel Kavşaklar için Kapasite Hesap Yöntemi, Doktora Tezi, İstanbul Teknik Üniversitesi FenBilimleri Enstitüsü, İstanbul.
  7. Tanyel, 2005 S. Tanyel; Yuvarlakada kavşaklarda anaakımdaki ağır araç yüzdesinin yanyol kapasitesi üzerindeki etkisi; Dokuz .Eylül Üniversitesi Mühendislik Fak. Fen ve Mühendislik Dergisi, 7 (1) (2005), pp. 19–30
  8. Tanley et al., 2013 S. Tanley, S.P. Caliskanelli, M.M. Aydin, S.S. Utku; An Investigation of Heavy Vehicle Effect on Traffic Circles; Teknil Dergi, 24 (4) (2013), pp. 6479–6504
Back to Top

Document information

Published on 05/04/17

Licence: Other

Document Score

0

Views 0
Recommendations 0

Share this document

claim authorship

Are you one of the authors of this document?